您现在的位置:网站首页答辩论文工学论文机械论文

毕业设计 杠杆的机械加工工艺及夹具设计

  • 简介:毕业设计-杠杆的机械加工工艺及夹具设计,共40页,14195字,附设计图纸、工序卡、任务书、开题报告等,通过对杠杆的材质及结构进行工艺分析,结合已修“机械制造工艺学”课程及机制工艺生产实习的知识,制订出一套在大批量生产条件下的杠
    类型:word+autocad    页数:40    字数:14195   
    资料包括:论文 图纸 任务书 开题报告   
    • 请与管理员联系购买资料 QQ:5739126
  • 论文简介
  • 相关论文
  • 论文下载
文件大小:3.87MB
适用专业:机械设计制造及其自动化
适用年级:大学
论文编号:203061

论文简介:
毕业设计-杠杆的机械加工工艺及夹具设计,共40页,14195字,附设计图纸、工序卡、任务书、开题报告等
通过对杠杆的材质及结构进行工艺分析,结合已修“机械制造工艺学”课程及机制工艺生产实习的知识,制订出一套在大批量生产条件下的杠杆的机械加工工艺规程,并设计其中两道工序的夹具。
主要技术要求:
机械加工工艺应基本合理
夹具结构合理,功能应能满足奔到工序的装夹要求,加工精度应达到工序规定的技术要求。
设计内容要求:
1)制定出杠杆的机械加工工艺规程一套(相当于一张A0图纸);
2)完成两道工序的夹具装配图(两张A0图纸);
3)测绘夹具零件图若干;
4)撰写一份字数约12000字的设计说明书。
摘 要:本设计是CA6140杠杆零件的加工工艺规程及一些工序的专用夹具设计。CA6140杠杆零件的主要加工表面是平面及孔。一般来说,保证平面的加工精度要比保证孔的加工精度容易。因此,本设计遵循先面后孔的原则。并将孔与平面的加工明确划分成粗加工和精加工阶段以保证孔的加工精度。基准的选择以杠杆外圆面作为粗基准,以孔及其下表面作为精基准。先将底面加工出来,然后作为定位基准,在以底面作为精基准加工孔。整个加工过程选用组合机床。在夹具方面选用专用夹具。考虑到零件的结构尺寸简单,夹紧方式多采用手动夹紧,夹紧简单,机构设计简单,且能满足设计要求。
关键词: 杠杆零件;加工工艺;夹具;定位;夹紧
Abstract:This paper is to design the craft processes of making the CA6140 lever spare parts and some specialized tongs in the process. The CA6140 lever spare part primarily processes the surface and bores. Generally speaking, to guarantee the accuracy of the flat surface process is easier than that of the bore. Therefore, this design follows the principle that surface first and then the bore, and definitely divides the process of flat surface and bore into coarse processes and precise processes to guarantee the bore processes. The basic choice is to consider 45 outside circle as rough basis and to consider 25 bore and its next surface as precise basis. The bottom is first processed out to be fixed position basis, and process the bore using the bottom as the precise basis. The whole processes choose the machine bed. In the aspects of tongs choosing, specialized tongs are used. In consideration of the simple construction size of the spare parts, clipping by hands is adopted. It is simple, and the organization design is simple, and can satisfy the design request.
Key Words:Lever spare parts;craft proces;tongs;fixed position;tight clip
目 录
摘要 1
关键词 1
1 前言 2
2 杠杆加工工艺规程设计 2
2.1 零件的分析 2
2.1.1 零件的作用 2
2.1.2 零件的工艺分析 2
2.2 杠杆加工的主要问题和工艺过程设计所应采取的相应措施 3
2.2.1 确定毛坯的制造形式 3
2.2.2 基面的选择 3
2.2.3 确定工艺路线 3
2.2.4 机械加工余量、工序尺寸及毛坯尺寸的确定 5
2.2.5 确定切削用量 7
2.2.6 确定基本工时 17
2.3 小结 22
3 专用夹具设计 22
3.1 加工工艺孔Φ25夹具设计 22
3.1.1 定位基准的选择 22
3.1.2 切削力的计算与夹紧力分析 23
3.1.3 夹紧元件及动力装置确定 24
3.1.4 钻套、衬套、钻模板及夹具体设计 24
3.1.5 夹具精度分析 26
3.1.6 夹具设计及操作的简要说明 27
3.2 粗精铣宽度为30mm的下平台夹具设计 27
3.2.1 定位基准的选择 27
3.2.2 定位元件的设计 28
3.2.3 定位误差分析 29
3.2.4 铣削力与夹紧力计算 29
3.2.5 夹具体槽形与对刀装置设计 30
3.2.6 夹紧装置及夹具体设计 32
3.2.7 夹具设计及操作的简要说明 33
3.3 钻M8螺纹孔夹具设计 33
3.3.1 定位基准的选择 33
3.3.2 定位元件的设计 34
3.3.3 定位误差分析 34
3.3.4 钻削力与夹紧力的计算 34
3.3.5 钻套、衬套、钻模板及夹具体设计 35
3.3.6 夹紧装置的设计 37
3.3.7 夹具设计及操作的简要说明 38
3.4 小结 38
4 总结 38
参考文献 39
致谢 40
附录1 40
附录2 40
附录3 40


论文文件预览:
共3文件夹,26个文件,文件总大小:3.87MB,压缩后大小:1.38MB

  • 毕业设计-杠杆的机械加工工艺及夹具设计
  • tangyyyyy
  • 新建文件夹
  • doc唐怡开题论证审批表.doc  [39.50KB]
  • doc任务书 .doc  [45.50KB]
  • doc开题论证记录唐怡.doc  [31.00KB]
  • doc东方08机制唐怡中期检查表.doc  [28.50KB]
  • dwg钻M8低孔装配图11.dwg  [112.16KB]
  • bak钻M8低孔装配图11.bak  [143.56KB]
  • dwg钻M8底孔夹具体零件图22.dwg  [127.63KB]
  • dwg钻25孔装配图11.dwg  [116.91KB]
  • dwg钻25孔夹具体零件图22.dwg  [101.97KB]
  • dwg铣平台夹具装配图11.dwg  [107.66KB]
  • dwg铣夹具体零件图22.dwg  [119.66KB]
  • doc唐怡过程卡片.doc  [70.00KB]
  • doc唐怡工序卡片10.doc  [28.50KB]
  • doc唐怡工序卡片9.doc  [29.00KB]
  • doc唐怡工序卡片8.doc  [53.00KB]
  • doc唐怡工序卡片7.doc  [40.50KB]
  • doc唐怡工序卡片6.doc  [78.50KB]
  • doc唐怡工序卡片5.doc  [76.50KB]
  • doc唐怡工序卡片4.doc  [59.00KB]
  • doc唐怡工序卡片3.doc  [62.50KB]
  • doc唐怡工序卡片2.doc  [54.50KB]
  • doc唐怡工序卡1.doc  [57.50KB]
  • doc唐怡杠杆加工工艺及夹具设计.doc  [2.10MB]
  • doc湖南农业大学东方科技学院2.doc  [42.50KB]
  • dwg杠杆零件图.dwg  [90.91KB]
  • bak杠杆零件图.bak  [93.25KB]

查看评论 已有0位网友发表了看法
  • 验证码: