您现在的位置:网站首页答辩论文工学论文电子论文

大连交通大学信息工程学院电子工艺实训(论文) 充电器的原理分析与制作

  • 简介:  大连交通大学信息工程学院电子工艺实训(论文) 充电器的原理分析与制作,共24页,10603字。
    类型:word   
    • 请与管理员联系购买资料 QQ:5739126
  • 论文简介
  • 相关论文
  • 论文下载
  大连交通大学信息工程学院电子工艺实训(论文) 充电器的原理分析与制作,共24页,10603字。
   摘 要
   实训电路图由稳压电源和充电器两部分组成:稳压电源输出3V、6V直流稳压电压,可作为收音机,录音机等小型电器的外接电源:充电器可对5号、7号可充电池进行恒流充电。充电器是采用电力电子半导体器件,将电压和频率固定不变的交流电变换为直流电的一种静止变流装置。充电的大部分时间还是采用恒压式充电,电池容易发热,使电解质容易分解从而影响电池的寿命。一般手机充电和数码相机的充电器都是采取这种充电方式。
   protel是Altium公司推出的电路辅助设计系统,是第一个将所有的设计工具集成于一身的板级设计系统。在原理图已完成的基础上利用Protel进行PCB设计一般遵循:确定外形、布局、布线、规则检查等几个步骤。分析了布局、布线的基本原则,探讨了在整个PCB设计过程中的一些经验和技巧。
  
   Abstract
   Training by the regulated power supply and battery charger circuit diagram of two parts: regulated power supply output of 3V, 6V DC voltage, can be used as radios, tape recorders and other small electrical appliances external power supply: charger can 5, 7, Rechargeable constant current charging the battery. Charger is the use of power electronic semiconductor devices, constant voltage and frequency of the alternating current to direct current conversion of a static inverter device. Charge most of the time or use of constant pressure charging, the battery easy to heat, so that electrolyte easier to break down thus affecting the battery life. Generally charge their cell phones and digital cameras to take this charger is charging.
   Altium has introduced protel is a circuit-aided design system, is the first one all the design tools integrated in a board-level design system. In the schematic diagram has been completed based on the use of Protel for PCB design in general, conform: identification of shape, layout, routing, rules, checks a few steps. Analysis of the layout, wiring the basic principles discussed throughout the PCB design process,some of the experiences and skills.
  
   关键词:直流稳压电源 充电器 Protel软件 PCB电路板的制作
   Keywords: DC Power ,Supply Charger ,Protel software, PCB circuit board production
  
   目 录
   一 Protel 软件的介绍………………………………………………………………………………1
   1.1 Protel 软件…………………………………………………………………………………1
   1.2 Protel 软件的发展…………………………………………………………………………1
   1.3 Protel 软件具体使用………………………………………………………………………1
   1.3.1原理图设计的一般步骤………………………………………………………………1
   1.3.2 原理图的绘制过程…………………………………………………………………2
   二 电路图的原理及各部分的介绍……………………………………………………………………3
   2.1 充电器的原理…………………………………………………………………………………4
   2.2 直流稳压电源及充电器的整体框图…………………………………………………………4
   2.3 单项桥式全波整流电路工作原理及参数计算………………………………………………5
   2.4滤波电路………………………………………………………………………………………5
   2.5 稳压电路………………………………………………………………………………………6
   2.6稳压电源的组成框图及波形图………………………………………………………………6
   2.7充电器部分……………………………………………………………………………………7
   三 PCB 电路板的制作………………………………………………………………………………8
   3.1 PCB 简介……………………………………………………………………………………8
   3.2 PCB的发展…………………………………………………………………………………8
   3.3 PCB的说明…………………………………………………………………………………8
   3.4 PCB板制作的具体步骤……………………………………………………………………8
   3.4.1 绘制正确的原理图和网络表…………………………………………………………8
   3.4.2 确定元件封装…………………………………………………………………………9
   3.4.3规划电路板……………………………………………………………………………9
   3.4.4导入网络表……………………………………………………………………………9
   3.4.5元件的布局……………………………………………………………………………9
   3.4.6 PCB布线………………………………………………………………………………10
   3.4.7保存和导出印制板文件………………………………………………………………10
   四 电路的焊接…………………………………………………………………………………………12
   4.1 元器件的检测…………………………………………………………………………………12
   4.1.1元器件的检查……………………………………………………………………………12
   4.1.2 确定安装方式及引脚处理………………………………………………………………12
   4.1.3 焊接电路…………………………………………………………………………………12
   4.1.4焊接处理及封装…………………………………………………………………………13
   4.2二极管、三极管的检测………………………………………………………………………13
   4.3 调试过程………………………………………………………………………………………14
   4.3.1 电路板的检测……………………………………………………………………………15
   4.3.2 输出电压的调试…………………………………………………………………………15
   五 调试结果……………………………………………………………………………………………15
   六 心得体会……………………………………………………………………………………………17
   七 谢辞…………………………………………………………………………………………………18
   八 参考文献…………………………………………………………………………………………19
   九 附录…………………………………………………………………………………………20
查看评论 已有0位网友发表了看法
  • 验证码: