论文简介：

毕业设计-凸轮箱体的加工工艺及夹具设计，正文共24页，15431字，附设计图纸
摘 要
本次毕业设计的题目是凸轮箱体的加工工艺及夹具设计。通过查阅机械工艺手册、夹具设计手册等资料，对工艺设计及夹具的设计有了较为全面的了解。零件是箱体类零件，根据凸轮箱体的特点，采用上下模板的夹具设计，该夹具采用一面两孔的定位，主要钻孔时有箱体里钻孔还有在箱体外钻孔的。钻孔时较为费劲，因此采用上下模板的夹具设计。
还有编排工艺中粗基准和精基准的选择，粗基准选择工件定面，精基准选择工件底座面。
加工工艺过程包括：毛坯的选择、基准的确定、机床类型的选定。夹具设计包括：定位元件、夹紧元件、上下模板设计、钻套的选择。机床选择包括：龙门铣床、摇臂钻床。
关键词：加工工艺；夹具设计；机床
Abstract
Part preseted by time of design examination questions is automobile half scrolls of casing pipe.Automobile half scrolls of casing pipe are one of important automobile component.The automobile running is to pass the centre transmission shaft from the engine,latter half axis driving force is transmitted to automobile queen bridge,drive a carriage wheel to be completed again from latter half axis.every has one half scrolls of casing pipe on queen bridge,on both side of retinue ,one holds and rear axle housing pressure compounds into an integral whole, another end installation has wheel hub axle bearing.And all weight that it is loaded with now that essential points bears the car body and wehicle,impingement force and moment of torsion easy to need to bear an automobile in the process running since the road is indignant but arouse,need to swear not to deformation happened in running,but to reovlve freely half scrolls within the person .
Arrangement desigeing that the problem is automobile half scrolls of casing pipe numerical control machine tool grip design and the workpiece treating handicraft’s time designs capital.The treating accomplishing end face and excircld to automobile half scrolls of casing pipe still having the inner hole is arranged,the machine tool designs out the clamp pretending to grip workpiece,machinery designing middle having wielded a great quantity in is time knowledge relatively.
Keywords： Process handicraft；Grip design； Machine tool
目 录
摘要 .....……Ⅰ
Abstract ....…Ⅱ
绪论 .....……1
1 机械加工工艺规程设计的任务和要求 ..……2
1.1设计工艺规程的基本要求 ...………2
1.2设计工艺规程的原始资料 ...………2
1.3设计工艺规程的内容步骤 ...………2
2 零件的机械加工工艺设计说明 ..…8
2.1 零件的分析 ....………8
2.2工艺规程的设计 ....…8
2.3机械加工余量和毛坯尺寸的确定 ...11
2.4选择各工序所用的机床、夹具、刀具和量具 ..…11
2.5确定切削用量 ....……14
2.6确定估算工时定额 ....14
3 专用夹具的设计 ...…16
3.1设计夹具的基本要求 ...…16
3.2设计夹具的依据 ....…16
3.3设计夹具的程序与内容 ...16
3.4 设计主旨 ....…18
3.5 机床夹具的设计 ....19
3.6 夹具设计及操作的简要说明 ...…21
结论 ....…22
致谢 ....…23
参考文献 .....24

论文文件预览：
共4文件夹，9个文件，文件总大小：1.20MB，压缩后大小：321.80KB

• 毕业设计-凸轮箱体的加工工艺及夹具设计
• 凸轮箱体工艺及夹具毕业设计
• 设计说明书
• 设计说明书
• 摘 要.doc  [41.50KB]
• 第一章 .doc  [152.50KB]
• 00装配图.exb  [137.04KB]
• 02长定位块.exb  [29.37KB]
• 03连结板.exb  [34.91KB]
• 04圆形定位块.exb  [24.51KB]
• 07导套.exb  [26.32KB]
• 凸轮箱体.exb  [275.42KB]
• 工艺.exb  [509.55KB]